Local

Replacing a Garage Floor Slab

The same work as a driveway in principle, done inside a building that is already standing, through one opening, against a door height that cannot move. What that changes, and what we will not touch.

A garage floor is flatwork like any other and it is the most constrained flatwork on a residential property. Everything about the job is decided by three things that were fixed before anyone thought about the concrete: the walls are already up, the door sets the finished height, and there is exactly one way in.

Why garage floors fail when driveways do not

The commonest cause is under the slab rather than on it. When a house or a garage is built, the ground around the foundation is excavated and then put back, and backfill settles for a long time afterwards. A garage floor frequently sits partly over that material, so it is starting from a worse base than a driveway on undisturbed ground.

Water is the other one. Vehicles bring snow and meltwater inside all winter, that water carries road salt, and the floor stays wet longer than an outdoor surface would because nothing dries it quickly. A floor with a poor fall holds it in the low spots, and those low spots are where the surface goes first.

Both of those are worth diagnosing properly before replacing anything. A floor replaced over backfill that is still moving will do the same thing again.

The three constraints that make it a different job

The door height cannot change. This is the one that decides the most. The finished floor has to arrive at the threshold at the right level, which means the new slab has to be the same thickness in the same place. There is no option to add depth, so if the old floor was thin, the answer is not simply to pour a thicker one.

Access is a single opening. Breaking out, carrying out and bringing in all happen through the door. On some sites a machine can work inside; on many it cannot, and then the removal is hand work. This is the biggest single variable in what a garage floor costs relative to the same area outside.

The building must not be disturbed. The walls stand on footings, and those footings are not part of this job. Taking out a floor means working to that edge deliberately rather than breaking back until something stops.

What we do and what we do not

We pour the slab: the excavation, the base, the reinforcement, the falls, the pour and the finish. That is the work.

Footings, foundation walls and anything that carries the structure are not ours and we do not pretend otherwise. This matters more than usual here, because if a garage floor has failed as a symptom of foundation movement, then replacing the floor is doing the second job first. You get a good floor for a short time and the same problem again.

So the first visit establishes which it is. A floor that has cracked and settled over soft backfill while the walls are plumb and sound is a flatwork job, and a straightforward one. A floor that has failed alongside signs of movement in the structure is a conversation to have with somebody else first, and we would rather say so and lose the job than take it.

How a replacement runs

  • Empty the garage. Entirely, and for longer than the pour day. This is worth planning early because it is the part that most often delays a start.
  • Break out and remove. Through the one opening, working to a clean edge at the perimeter.
  • Deal with what is underneath. The point of the exercise. Poor or settled material comes out and is replaced with granular fill compacted in layers, which is the only moment anybody can do anything about the real cause.
  • Set the falls. To the door, or to a drain if there is one, so meltwater leaves rather than standing.
  • Pour, finish and joint. Joints laid out for the shape of the floor, with a finish that is not slick when wet.
  • Stay off it. Longer than you would like, and vehicles later than footsteps. The crew will give you the real timings on the day.

Plan for the garage being unusable

The part people underestimate is not the pour, it is the weeks either side of it. A garage full of things that have accumulated for a decade has to be emptied completely, and there has to be somewhere for all of it to go that is not the driveway the crew needs.

Then the floor has to be left alone afterwards, footsteps first and vehicles considerably later, with the real timings given on the day rather than guessed from an article. Booking this work for a week when two cars have nowhere else to stand is the commonest self-inflicted difficulty on an otherwise straightforward job.

When an overlay is the better answer

If the slab is structurally sound and the complaint is the surface, the door-height constraint that rules out a thicker pour also makes a thin bonded overlay attractive, because it adds very little height. The test is the same two-part one that applies to any resurfacing: sound concrete, and nothing moving. Both have to be true.

That two-part test is argued out in resurfacing vs replacing concrete. Where it is the surface that has gone and not the slab beneath it, the causes are covered in why concrete scales and flakes. To have the work quoted, see concrete repair; for figures by use case, what a concrete slab costs.

Get My Free Estimate

Get your free, on-site estimate.

Tell us about your project and we'll call you back the same day to set up a free measure and price.

Get your free quote

Tell us about your project and we will call you back the same day. No obligation.

What are you looking to do?

Free, no-pressure estimate · Serving Lake County, IL

By submitting, you agree to our Privacy Policy and Terms, and consent to be contacted by phone, text, or email about your project, including by automated means. Consent isn't a condition of purchase. Msg & data rates may apply.

Call (262) 228-5293 Text us