Local
Replacing a Driveway Apron
The few feet nearest the street are not really your driveway, are usually built to a different specification, and are the first part to fail. Why it is a separate line on every honest quote.
Almost nobody calls us about an apron. They call about a driveway, and somewhere in the first minute it becomes clear that the part that has actually broken up is the last stretch before the road. That section behaves differently from everything behind it because it is doing a different job on ground that is not yours, and understanding that changes both what the work involves and what it costs.
Where your driveway stops
Your property line is not the kerb. Between the two sits the right-of-way, a strip the municipality controls, and the apron is the piece of concrete that crosses it.
It looks continuous with your driveway and it is treated as a separate structure. The Village sets its specification, the Village inspects it, and you generally pay for it. That combination catches people out, because it is the only part of a private driveway where the homeowner does not get to decide how it is built.
Why it fails first
Look down a street and the pattern is consistent. The apron is cracked or crumbling while the driveway behind it is fine. There are four reasons and they compound:
- Vehicles turn on it under load. Every car entering or leaving twists across that section rather than driving straight over it.
- It takes the heaviest traffic on the property. Refuse lorries, delivery vans and anything that mounts the kerb crosses the apron and often nothing else.
- It gets the most salt. Road salt is carried onto it directly by tyres and pushed onto it by the plough, so the apron takes a chemical load the rest of the driveway never sees.
- It sits where the ground is most disturbed. Utilities, kerb works and road construction all pass through that strip, so the material beneath it is frequently the least consolidated on the site.
An apron that has gone while the driveway has not is therefore normal rather than a sign that the original job was bad.
The specification is not yours to choose
This is the practical heart of it. A residential driveway starts at four inches. An apron is whatever the right-of-way specification says, and that is a local decision that varies more than people expect between neighbouring municipalities. Franklin, over in Wisconsin, requires seven inches. That figure is not Gurnee's and we quote it only to make the point: there is no default apron thickness, and assuming four inches because that is what driveways are is how work gets rejected at inspection.
The same applies to the material, the jointing, how the apron meets the kerb and gutter, and the fall across it. All of that comes from the Village rather than from a contractor's habit, and it is established before quoting rather than discovered during the pour.
The permit is the first step, not the last
Nothing happens on that strip without the Village agreeing to it first, and the requirement does not soften for a straight like-for-like rebuild. There is no version of an apron job that sits outside it.
That brings a lead time, contractor bonding and insurance requirements, and inspections, and it means an apron cannot be squeezed onto the end of a job as an afterthought. All of the detail sits in the Gurnee driveway apron permit, start to finish, which is the page to read before booking anything that touches the street.
The consequence worth planning around is sequencing. Because the apron carries a permit and a timeline while the driveway behind it does not, the two halves of an apparently single job move at different speeds. A contractor who raises that at quoting stage has done this before.
The kerb question
One detail worth raising before work starts, because it can change the scope. Where an apron meets the street, there is usually kerb and gutter, and the condition of that kerb is not always good. If it has been broken by a plough or crushed by something heavy, rebuilding the apron up to a damaged kerb produces a new surface meeting an old defect, and water will find the join.
Whether the kerb is the Village's responsibility or forms part of your permitted work depends on the situation and on who damaged it. It is a short question to ask at permit stage and an awkward one to discover with a crew on site.
Doing it with the driveway, or on its own
The economics point firmly toward doing both together where both need doing. Mobilising a crew, a mixer and a disposal route is a fixed cost, and an apron on its own carries all of it while covering a small area. Add it to a driveway replacement and the marginal cost is much lower.
Replacing only the apron makes sense when the driveway behind it is genuinely sound and has years left. That happens often enough, and in that case it is a contained job: cut a straight line, take out the failed section, rebuild the base, pour to the Village specification, joint it cleanly at the boundary.
One expectation to set. A new apron against an older driveway will not match in colour, and no contractor can make it. What can be controlled is a straight joint line and a consistent finish, which is the difference between looking deliberate and looking patched. The same issue comes up when adding width, and it is covered in widening a concrete driveway.
Apron and driveway quoted as one piece of work is our concrete driveway page; for where the money goes, see the Gurnee driveway cost breakdown.
Sources
- Village of Gurnee - right-of-way permit requirement covering replacement work, and local specification enquiries.
- Illinois Ready Mixed Concrete Association - homeowner guidance on residential driveway construction.